Nissan Ariya: Dtc/circuit Diagnosis

• B0001-09 Driver Air Bag Module
• B0091-86 Front Door Satellite Sensor
• B0094-55 Crash Zone Sensor
• B1000-49 Air Bag Diagnosis Sensor Unit
• B1000-55 Air Bag Diagnosis Sensor Unit
• B1036-16 Ignition Voltage
• B1040-22 Vehicle Speed
• B1041-82 Vehicle Speed Signal
• B12b5-97 Frontal Collision Detection
• U0073-00 Can Comm Circuit

B0001-09 Driver Air Bag Module

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B0001-09	Driver Frontal Stage 1 Deployment Control	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Driver air bag module signal
		Threshold	Driver air bag module circuit is shorted to other (including the spiral cable)
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

• Connection malfunction or short circuit of harness and connector

• Internal malfunction of driver air bag module

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 2.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace malfunctioning harness and connector.

REPLACE SPIRAL CABLE

1. Replace spiral cable. Refer to Removal & Installation.

2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE DRIVER AIR BAG MODULE

1. Replace driver air bag module. Refer to Removal & Installation.

2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B0091-86 Front Door Satellite Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B0091-86	Left Side Restraints Sensor 1	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Front door satellite sensor LH signal
		Threshold	Front door satellite sensor LH is out of the specified specification
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

Air bag diagnosis sensor unit and front door satellite sensor LH is different from the part specified

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE FRONT DOOR SATELLITE SENSOR LH

1. Replace front door satellite sensor LH. Refer to Removal & Installation.

2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B0094-55 Crash Zone Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B0094-55	Center Frontal Restraints Sensor	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Crash zone sensor signal
		Threshold	When a mismatch is detected between in the configuration data stored in the air bag diagnosis sensor unit and Nissan Ariya vehicle specification.
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

• Connection malfunction of harness and connector

• Mistake of configuration for air bag diagnosis sensor unit

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 2.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace malfunctioning harness and connector.

PERFORM CONFIGURATION

1. Perform configuration for air bag diagnosis sensor unit. Refer to Description.

2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1000-49 Air Bag Diagnosis Sensor Unit

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B1000-49	Air bag diagnosis sensor unit	Diagnosis condition	When power switch is ON.
		Signal (terminal)	—
		Threshold	Air bag diagnosis sensor unit is malfunctioning
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

Malfunction in air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1000-55 Air Bag Diagnosis Sensor Unit

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B1000-55	Air bag diagnosis sensor unit	Diagnosis condition	When power switch is ON.
		Signal (terminal)	—
		Threshold	When no data are stored in the air bag diagnosis sensor unit
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

Incomplete of configuration for air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM CONFIGURATION

Perform configuration for air bag diagnosis sensor unit.

>>

Refer to Description.

B1036-16 Ignition Voltage

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B1036-16	Ignition voltage	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Ignition low voltage signal
		Threshold	Power supply malfunction (low voltage) of air bag diagnosis sensor unit
		Diagnosis delay time	10 seconds or more.

POSSIBLE CAUSE

• Malfunction of battery voltage (9 V or less)

• Connection malfunction of harness or connector

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON and wait for 10 seconds or more.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK BATTERY VOLTAGE

Check battery voltage. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning parts.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 3.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace malfunctioning harness and connector.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1040-22 Vehicle Speed

DTC Description

DTC DETECTION LOGIC

NOTE:

This DTC may be detected when drive the Nissan Ariya vehicle at vehicle speed of 300 km/h (186 MPH) or more.

DTC No.	CONSULT screen items	DTC Detection Condition
B1040-22	Nissan Ariya Vehicle speed	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Nissan Ariya Vehicle speed signal
		Threshold	300 km/h (186 MPH) or more
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

• Drive the vehicle at vehicle speed of 300 km/h (186 MPH) or more.

• VCM

• Air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

REPLACE VCM

1. Replace VCM. Refer to VCM : Removal & Installation.

2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

NO>>

INSPECTION END

B1041-82 Vehicle Speed Signal

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B1041-82	Nissan Ariya Vehicle speed signal	Diagnosis condition	When power switch is ON.
		Signal (terminal)	CAN communication signal
		Threshold	Error signal that is received from ABS actuator and electric unit (control unit)
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

• ABS actuator and electric unit (control unit)

• Air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC B1041-82 is displayed with DTC U0073-00, first perform the trouble diagnosis for DTC U0073-00.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK DTC PRIORITY

If DTC B1041-82 is displayed with DTC U0073-00, first perform the trouble diagnosis for DTC U0073-00.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS

Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

B12b5-97 Frontal Collision Detection

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
B12B5-97	Frontal collision	Diagnosis condition	When power switch is ON.
		Signal (terminal)	Collision signal
		Threshold	Frontal collision detected
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

Frontal collision

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

WARNING:

• Before servicing, power switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis. Refer to When SRS is activated in a collision or When SRS is not activated in a collision.

>>

GO TO 2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

When DTC B12B5-97 is detected, replace air bag diagnosis sensor unit.

>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

U0073-00 Can Comm Circuit

DTC Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.	CONSULT screen items	DTC Detection Condition
U0073-00	Control Module Communication Bus "A" Off	Diagnosis condition	When power switch is ON.
		Signal (terminal)	CAN communication signal
		Threshold	Air bag diagnosis sensor unit cannot communicate CAN communication signal.
		Diagnosis delay time	2 seconds or more.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

1. Power switch ON and wait for 2 seconds or more.

2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

INSPECTION END