english german french spanish
Nissan

Nissan Ariya: Dtc/circuit Diagnosis

Nissan Ariya (FE0) 2023-2025 Service & Repair Manual / Body Interior / Instrument Panel / Dtc/circuit Diagnosis

Power Supply and Ground Circuit (center Console Finisher)

Diagnosis Procedure

CHECK FUSE

Check that the following fuses are not blown (open).

Location Fuse No. Capacity
Fuse block (J/B) 53 10A
8 10A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect center console finisher connector.

  3. Check voltage between center console finisher harness connector and ground.

    ＋ - Condition Voltage
    Center console finisher
    Connector Terminal
    M204 1 Ground Power switch OFF (auto ACC status) or ON Battery voltage
    Other than above 0 V
    2 ON Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK GROUND CIRCUIT

  1. Power switch OFF.

  2. Check continuity between center console finisher harness connector and ground.

Center console finisher ― Continuity
Connector Terminal
M204 16 Ground Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair the harness or connector.

Console Slide Switch

Component Function Check

CHECK CONSOLE SLIDE SWITCH FUNCTION

  1. Power switch ON.

  2. Select “DRIVER SEAT” using CONSULT.

  3. Select “Console slide switch (Forward)” and "Console slide switch (Backward)" in “Data monitor” mode.

  4. Check that the function operates normally according to the following conditions.

    Monitor item Condition Status
    Console slide switch (Forward) Console slide switch (forward side) Push On
    Release Off
    Console slide switch (Backward) Console slide switch (backward side) Push On
    Release Off

Is the inspection result normal?

YES>>

Console slide switch is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK CONSOLE SLIDE SWITCH POWER SUPPLY VOLTAGE

  1. Power switch OFF.

  2. Disconnect console slide switch connector.

  3. Check voltage between console slide switch harness connector and ground.

    ＋ −

    Voltage

    (Approx.)
    Console slide switch
    Connector Terminal
    M213 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK CONSOLE SLIDE SWITCH GROUND CIRCUIT

  1. Disconnect driver seat control unit connector.

  2. Check continuity between console slide switch harness connector and driver seat control unit harness connector.

    Console slide switch Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    M213 4 B313 32 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harness or connector.

CHECK CONSOLE SLIDE SWITCH POWER SUPPLY CIRCUIT

  1. Disconnect driver seat control unit connector.

  2. Check continuity between console slide switch harness connector and driver seat control unit harness connector.

    Console slide switch Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    M213 1 B313 25 Existed

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK CONSOLE SLIDE SWITCH

Check console slide switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Replace console slide switch. Refer to Removal & Installation.

Component Inspection

CHECK CONSOLE SLIDE SWITCH

  1. Power switch OFF.

  2. Disconnect console slide switch connector.

  3. Check continuity between console slide switch terminals.

    Console slide switch Condition Resistance (Ω)
    Terminal
    1 4 Console slide switch Operate forward side switch 399 - 455
    Operate backward side switch 241 - 287
    Release 7276 - 8235

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace console slide switch. Refer to Removal & Installation.

Console Slide Motor

Component Function Check

CHECK CONSOLE SLIDE MOTOR FUNCTION

  1. Power switch ON.

  2. Select “DRIVER SEAT” using CONSULT.

  3. Select “Console slide motor” in “Active test” mode.

  4. Check that the function operates normally according to the following conditions.

    Test item Operation
    Console slide motor Up Console slide upper Forward
    Down Backward
    Stop Stop

Is the inspection result normal?

YES>>

Console slide motor is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK CONSOLE SLIDE MOTOR OPERATION SIGNAL

  1. Power switch OFF.

  2. Disconnect console slide motor connector.

  3. Check voltage between console slide motor harness connector and ground.

    ＋ − Condition

    Voltage

    (Approx.)
    Console slide motor
    Connector Terminal
    M201 1 Ground Console slide upper Backward operation 13.5 V
    Other than above 0 – 1 V
    2 Forward operation 13.5 V
    Other than above 0 – 1 V

Is the inspection result normal?

YES>>

Replace center console assembly. Refer to Removal & Installation.

NO>>

GO TO 2.

CHECK CONSOLE SLIDE MOTOR OPERATION SIGNAL CIRCUIT

  1. Disconnect driver seat control unit connector.

  2. Check continuity between console slide motor harness connector and driver seat control unit harness connector.

    Console slide motor Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    M201 1 B465 41 Existed
    2 42

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Flexible Center Storage Motor

Diagnosis Procedure

CHECK FLEXIBLE CENTER STORAGE MOTOR OPERATION SIGNAL

  1. Power switch OFF.

  2. Disconnect flexible center storage motor connector.

  3. Check voltage between flexible center storage motor harness connector and ground.

    ＋ - Condition

    Voltage

    (Approx.)
    Flexible center storage motor
    Connector Terminal
    M632 1 Ground Flexible center storage OPEN/CLOSE switch Push OPEN switch 12 V
    Release 0.13 V
    3 Push CLOSE switch 12 V
    Release 0.13 V

Is the inspection result normal?

YES>>

Replace flexible center storage assembly. Refer to Removal & Installation.

NO>>

GO TO 2.

CHECK FLEXIBLE CENTER STORAGE MOTOR OPERATION SIGNAL CIRCUIT

  1. Disconnect flexible center storage control module connector.

  2. Check continuity between flexible center storage motor harness connector and flexible center storage control module harness connector.

    Flexible center storage motor Flexible center storage control module Continuity
    Connector Terminal Connector Terminal
    M632 1 M622 14 Existed
    3 18

Is the inspection result normal?

YES>>

Replace flexible center storage assembly. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

Flexible Center Storage Open/close Switch Circuit

Diagnosis Procedure

CHECK FLEXIBLE CENTER STORAGE OPEN/CLOSE SWITCH SIGNAL

  1. Power switch OFF.

  2. Check voltage between flexible center storage control module harness connector and ground.

    ＋ - Condition

    Voltage

    (Approx.)
    Flexble center storage control module
    Connector Terminal
    M621 8 Ground Flexible center storage OPEN/CLOSE switch Push OPEN switch 5 V
    Release 0 V
    9 Push CLOSE switch 5 V
    Release 0 V

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 2.

CHECK FLEXIBLE CENTER STORAGE OPEN/CLOSE SWITCH SIGNAL CIRCUIT

  1. Disconnect flexble center storage control module connector and center console finisher connector.

  2. Check continuity between flexble center storage control module harness connector and center console finisher harness connector.

    Flexble center storage control module Center console finisher Continuity
    Connector Terminal Connector Terminal
    M621 8 M204 8 Existed
    9 9

Is the inspection result normal?

YES>>

Replace center console finisher. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

Flexible Center Storage Full Close/open Switch Circuit

Diagnosis Procedure

CHECK FLEXIBLE CENTER STORAGE FULL CLOSE/OPEN SWITCH SIGNAL

  1. Power switch ON.

  2. Check voltage between flexible center storage control module harness connector and ground.

    ＋ - Condition

    Voltage

    (Approx.)
    Flexible center storage control module
    Connector Terminal
    M621 5 Ground Flexible center storage lid Full close 0 V
    Other than above 5 V
    6 Full open 0 V
    Other than above 5 V

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace flexible center storage assembly. Refer to Removal & Installation.

Vehicle Speed Signal Circuit

Diagnosis Procedure

CHECK VEHICLE SPEED SIGNAL

  1. Power switch OFF.

  2. Disconnect flexible center storage control module connector and combination meter connector.

  3. Check continuity between flexible center storage control module harness connector and combination meter harness connector.

    Flexible center storage control module Combination meter Continuity
    Connector Terminal Connector Terminal
    M621 3 M98 12 Existed

  4. Check continuity between flexible center storage control module harness connector and ground.

    Flexible center storage control module ― Continuity
    Connector Terminal
    M621 3 Ground Not existed

Is the inspection result normal?

YES>>

Replace integrated interface display (combination meter). Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Close Reminder Circuit

Diagnosis Procedure

CHECK CLOSE REMINDER SIGNAL

Check voltage between center console finisher harness connector and ground.

＋ - Condition

Voltage

(Approx.)
Center console finisher
Connector Terminal
M204 7 Ground Nissan Ariya Vehicle speed More than 15 km/h (9.3 MPH) 1.2 V
Less than 15 km/h (9.3 MPH) 0 V

Is the inspection result normal?

YES>>

Replace center console finisher. Refer to Removal & Installation.

NO>>

GO TO 2.

CHECK CLOSE REMINDER SIGNAL CIRCUIT

  1. Disconnect flexible center storage control module connector and center console finisher connector.

  2. Check continuity between flexible center storage control module harness connector and center console finisher harness connector.

    Flexible center storage control module Center console finisher Continuity
    Connector Terminal Connector Terminal
    M621 10 M204 7 Existed

  3. Check continuity between flexible center storage control module harness connector and ground.

    Flexible center storage control module ― Continuity
    Connector Terminal
    M621 10 Ground Not existed

Is the inspection result normal?

YES>>

Replace flexible center storage assembly. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

 
next pagenext pageSystemSymptom Diagnosisnext pagenext page

Nissan Ariya (FE0) 2023-2025 Service & Repair Manual

Dtc/circuit Diagnosis

Actual pages

Beginning midst our that fourth appear above of over, set our won’t beast god god dominion our winged fruit image

More Nissan autos

More Nissan Manuals

More Manuals

© 2023-2025 Copyright www.niariya.com